# Robot control: motion, path planning and safety

Robot control is the part of a TOS Robotics cell that moves the arm. The AI model gives a pick pose and a place pose. Robot control gets the arm there on a moving belt, within its limits and on time. We drive FANUC arms in production and our own TOS Robot.

Source: https://tosrobotics.com/capabilities/robot-control/
Last updated: 2026-11-20

- In production: FANUC controller with line tracking
- Streaming: A joint target every 4 ms
- Planner: Jerk-limited, our own
- Safety: Certified hardware, apart from the AI

A robot controller picks its own timing for every corner. **Where that is not good enough, our planner takes over.**

## What we build

- **Line tracking.** On the bell pepper line the FANUC controller tracks the belt itself. Our cells pick while the belt moves.

- **Path planning.** Our planner limits speed, acceleration and jerk. Offline it needed less time than the FANUC planner for the same moves. It is not yet used on a production robot.

- **Motion streaming.** Every 4 ms our PC gives the robot its next joint position, so we set the timing and the limits. We use it for [cream on cakes](https://tosrobotics.com/cases/cream-dispensing-on-cakes/), where a taught pattern keeps its own timing on a moving belt.

- **Limits and stops.** Our streaming planner for the cream line stays below the limits of the controller, and any alarm is a stop with the motor power off. Poses that the joint limits or safety zones would block are filtered out of the training data.

- **Measured on real cycles.** We judge each change on the logged position of the robot, every 4 ms, over tens of thousands of cycles.

## Where it is used

- [Flowpacking cell: robots that fill the flowpacker](https://tosrobotics.com/products/flowpacking-cell/): A complete cell that fills the flowpacker. €150,000 per cell. In production.
- [TOS Robot: a robot arm for high-speed picking and placing](https://tosrobotics.com/products/tos-robot/): Our own robot arm for high-speed picking and placing. Three arms on one beam.
- [AI robot control software that runs a robot cell](https://tosrobotics.com/products/ai-robot-control-software/): The software that runs a robot cell. Licence for robots of any brand.

## Keep reading

- [Why a taught robot path cannot simply be sped up](https://tosrobotics.com/research/why-taught-robot-paths-cannot-be-sped-up/): Raise the speed and a blended corner moves. On our robots the same CNT50 corner cut 14 mm from a standstill and 24 mm from a moving start.
- [How do you make ACT move a robot arm smoothly?](https://tosrobotics.com/research/smooth-robot-motion-with-act/): ACT took 17.1 ms per prediction on average on our robot and 97.9 ms at worst. The chunk handover is sized for the slow case.

## Questions and answers

### Which robots does TOS Robotics control?

FANUC arms on the bell pepper line, and the [TOS Robot](https://tosrobotics.com/products/tos-robot/), which uses our own planner from the start.

### Does the belt have to stop for a pick?

No. Every TOS Robotics cell tracks the belt, so the robot picks while the belt moves or stands still. This is called line tracking.

### Why not let the robot controller plan the whole path?

Because the controller rounds a corner differently at another speed. On our robots the same corner was cut by 14 mm when the arm started from rest and by 24 mm when it arrived moving. [Why a taught robot path cannot simply be sped up](https://tosrobotics.com/research/why-taught-robot-paths-cannot-be-sped-up/) has what we measured.

### Is the robot safe next to people?

A TOS Robotics cell is a guarded industrial cell. The AI decides where to pick and place. The safety of the cell is handled by certified safety hardware, separate from the AI.
